Hotpoint CTD85A Návod k použití stáhnout pdf (Strana 5)

Installation

Important

Information

Installation

Description

Start and

Programmes Laundry

Warnings and

Suggestions

Maintenance

and Care

Service

Troubleshooting

Where to put your dryer

●

Place your dryer at a distance from gas ranges,

stoves, heaters, or cook tops because flames can

damage the appliance.

●

If you are going to install the

appliance under a work

counter, be sure to leave a

10mm space between the top

and any other objects on or

above the machine and a

15mm space between the

sides and lateral furnishings or

walls.

This is to ensure proper air circulation.

! Make sure that the back vents are not obstructed.

Ventilation

When the dryer is in use, there has to be adequate

ventilation. Make sure you put your dryer in an

environment that is not damp and has proper air

circulation throughout. Airflow around the dryer is

essential to condense the water produced during the

washing, the dryer will not operate efficiently in an

enclosed space or cupboard.

! If using the dryer in a small or cold room some

condensation could be experienced.

! We do not recommend that the dryer is installed in a

cupboard but the dryer must never be installed

behind a lockable door, a sliding door or a door with a

hinge on the opposite side to that of the dryer door.

Door Reversal Instructions

The door of your dryer is reversible and can easily be

changed. Exchange diagonally hinge brackets and

blanking screws. Exchange door latch and catch with

their opposite blanking plates (see diagram above).

Water drain

If your dryer is installed next to a drain the water can be

plumbed into this drain. This does away with the need to

empty the water container (

see Plumbing your Dryer

Electrical connections

Make sure of the following before you insert the plug

into the the electrical socket:

●

The socket must be grounded.

●

The socket must be able to sustain the machines

maximum power, which is indicated on the rating

label (see Dryer Description).

●

Power voltage must be within the values indicated on

the rating label (see Dryer Description).

●

The socket must be compatible with the dryers plug.

●

Should this not be the case, replace the plug or the socket.

! Do not use extension cords.

! The dryer must not be installed outdoors, even if the

space is sheltered. It can be very dangerous if it is

exposed to rain or storms.

! Once installed, the dryers electrical wire and plug

must be within easy reach.

! The power cord must not be bent or squashed.

! The power cord supplied is fitted with a BS1363 plug

and a 13 amp BS1362 fuse. If you need to replace the

fuse, use only those rated at 13 amp (13A) and ASTA

approved to BS1362.

Moulded plug

! The plug must not be used

without the fuse cover in place.

If a replacement fuse

holder/cover is required, it must

be of the same colour coding or

wording as shown on the base of

the plug.

Replacements are available from

authorised dealers.

Changing the plug

The wires in the power cord are coloured in accordance

with the following:

! If the plug being replaced is a non-rewirable type,

then the cut-off plug must be disposed of safely. DO

NOT leave it where it can be inserted into a socket and

create a shock

hazard.

! The power supply cord should be checked periodically

and replaced by a cord specially prepared for this dryer

and fitted only by authorised technicians (see Service).

New or longer power cords are supplied at an extra

charge by authorised dealers.

! The manufacturer denies any responsibility should

any of these rules not be followed.

! If in doubt about any of the above consult a qualified

electrician.

Before you start using your dryer

Once you have installed your dryer and before you use

it, clean the inside of the drum to remove any dust

that could have accumulated during transport.

Minimum gap 10mm

Minimum gaps

15mm

Door catch

Door latch

Hinge

Green and Yellow

(Earth) wire to terminal

marked ‘E’, symbol ,

or coloured green and

yellow.

Blue (Neutral) wire to

terminal marked ‘N’ or

coloured black.

Cord clamp

13A ASTA approved

fuse to BS1362.

Brown (Live) wire to

terminal marked ‘L’

or coloured red.

1 2 3 4 5 6 7 8 9 10 ... 15 16

Komentáře k této Příručce

Žádné komentáře

Hotpoint CTD85A Návod k použití Strana 5

Komentáře k této Příručce

Související produkty a manuály pro Pračky Hotpoint CTD85A